MHD F+G Series

The MHD Flasher F+G Series is a complete flash tuning app for your BMW. Unlike a piggyback module, it is capable of complete DME remapping while retaining all OEM safety mechanisms. This allows for maximum performance,maximum safety, and unrivaled drivability. --------------------------------------------- Full OBD Flashing: You can install MHD right at home and start tuning immediately! There is no need to remove and send out your DME for a costly “unlock.” Simply download the MHD Flasher F-Series app that connects via a K+DCAN cable to your Android device and your vehicle’s OBD-II port, start the app, and within 15-25 minutes the initial installation is complete. Further map changes are much faster - only 1-3 minutes! You can revert your vehicle to the factory OEM flash at any point, and no initial backup is necessary. --------------------------------------------- Stage 1, Stage 2 und E85 OTS (Off The Shelf) Maps by PureBoost: N55 EWG (Vehicles built after 07/2013 with electronic wastegate): - Stage 1 (up to 360HP/540NM) (not available for M2 and X4 M40i) - Stage 2 (up to 390HP/580NM) - Stage 2+ (up to 430HP/630NM) - Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20% N55 PWG (pneumatic wastegate): - Stage 1 (up to 340HP/540NM) - Stage 2 (up to 370HP/580NM) - Stage 2+ (up to 400HP/630NM) - Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20% S55 (BMW M3 / M4 F8x): - Stage 1 (up to 530HP/700NM) - Stage 2 (up to 560HP/780NM) - Ethanol Mix Maps: Stage 1, 2 and 2+ E30 Maps for ethanol blends of 30% B58: - Stage 1 (up to 420HP/580NM) - Stage 2 (up to 470HP/630NM) - Ethanol Mix Maps: Stage 1, 2 Maps for ethanol blends of 30% --------------------------------------------- Monitor your engine behavior to make sure it is running perfectly using a configurable and very responsive gauge layout. 50+ engine parameters are available at a glance! These are some of the available monitors: - Boost, Boost Target - Lambda (AFR) - Intake Air Temp (IAT) - Ignition Timing per Cylinder - Coolant Temperature - Oil Temperature, Oil Pressure - Transmission Temperature - High Pressure Fuel Pump (HPFP) - Throttle Position - Wastegate Duty-Cycle (WGDC) - RPM - Speed - EGT And many more… MHD exclusive advanced monitor: - Timing Corrections per Cylinder - Boost target EX which can read higher than 22.x psi (the BMW boost target channel can't) - Base Compressor Axis: Boost Setpoint, MAF req WGDC. - Active Torque Limiters And many more… --------------------------------------------- These flash options can be applied to any map directly through the app: - Exhaust Burble (duration & aggressiveness, min speed, min rpm) - N20 Map Sensor (on N55) - Remove top speed limiter (Vmax) - Cold start noise reduction - Exhaust flap open in sport mode - Limit power per gear - XHP TCU flash support (optimizied OTS maps) - Sport cooling mode for increased water / air intercooler cooling (B58 only) --------------------------------------------- Supported Cars: M135i F2x N55 2012 - 2016 M235i F2x N55 2013 - 2016 M2 F87 N55 2015 - 2018 335i N55 F3x 2011 - 2015 435i N55 F3x 2013 - 2016 535i / GT N55 F1x 2010 - 2017 640i N55 F0x 2011 - 2017 740i N55 F0x 2012 - 2015 X3 35i N55 F25 2010 - 2017 X4 35i / M40i N55 F26 2014 - 2018 X5 40i N55 F15 2013 - 2018 X6 40i N55 F16 2014 - 2018 M3 S55 F80 2014 - 2019 M4 S55 F82 2014 - 2019 M4 S55 F83 2014 - 2019 M140i F2x 2012 - 2019 M240i F2x 2016 - 2019 340i F3x 2015 - 2019 440i F3x 2016 - 2019 540i G3x 2017 - 640i GT G32 2017 - 740i G1x F0x 2015 - X3 M40i G01 2017 - X4 M40i G02 2018 - X5 40i G05 2018 - Z4 M40i G29 2019 - 114i F2x 2012 - 2015 116i F2x 2011 - 2015 118i F2x 2011 - 2016 120i F2x 2015 - 2017 316i F3x 2012 - 2018 X-Drive is supported on all cars. All performance power kit cars are supported. Check out our homepage / user manual for more information and recommended modifications for each stage. La serie F + G MHD Flasher è un'app completa per la regolazione della luminosità della tua BMW. A differenza di un modulo piggyback, è in grado di completare la rimappatura DME mantenendo tutti i meccanismi di sicurezza OEM. Ciò consente prestazioni massime, massima sicurezza e guidabilità senza rivali. --------------------------------------------- Lampeggio OBD completo: È possibile installare MHD direttamente a casa e iniziare subito la sintonizzazione! Non è necessario rimuovere e inviare il DME per un costoso "sblocco". Basta scaricare l'app MHD Flasher F-Series che si collega tramite un cavo K + DCAN al dispositivo Android e alla porta OBD-II del veicolo, avviare l'app e entro 15-25 minuti l'installazione iniziale è completa. Ulteriori modifiche alla mappa sono molto più veloci - solo 1-3 minuti! È possibile ripristinare il veicolo in fabbrica in qualsiasi momento, e non è necessario alcun backup iniziale. --------------------------------------------- Mappe Stage 1, Stage 2 e E85 OTS (Off The Shelf) di PureBoost: N55 EWG (veicoli costruiti dopo il 07/2013 con wastegate elettronico): - Fase 1 (fino a 360 HP / 540 NM) (non disponibile per M2 e X4 M40i) - Fase 2 (fino a 390 HP / 580 NM) - Stage 2+ (fino a 430 HP / 630 NM) - Mappe di miscela di etanolo: Stage 1, 2 e 2+ E20 Mappe per miscele di etanolo del 20% N55 PWG (wastegate pneumatico): - Fase 1 (fino a 340 HP / 540 NM) - Fase 2 (fino a 370 HP / 580 NM) - Stage 2+ (fino a 400 HP / 630 NM) - Mappe di miscela di etanolo: Stage 1, 2 e 2+ E20 Mappe per miscele di etanolo del 20% S55 (BMW M3 / M4 F8x): - Fase 1 (fino a 530 HP / 700 NM) - Fase 2 (fino a 560 HP / 780 NM) - Mappe di miscela di etanolo: Mappe Stage 1, 2 e 2+ E30 per miscele di etanolo del 30% B58: - Fase 1 (fino a 420 HP / 580 NM) - Stage 2 (fino a 470HP / 630NM) - Mappe di miscela di etanolo: Stage 1, 2 mappe per miscele di etanolo del 30% --------------------------------------------- Monitora il comportamento del tuo motore per assicurarti che funzioni perfettamente utilizzando un layout di gauge configurabile e molto reattivo. 50+ parametri del motore sono disponibili a colpo d'occhio! Questi sono alcuni dei monitor disponibili: - Aumenta, aumenta il bersaglio - Lambda (AFR) - Intake Air Temp (IAT) - Tempo di accensione per cilindro - Temperatura del refrigerante - Temperatura dell'olio, pressione dell'olio - Temperatura di trasmissione - Pompa del carburante ad alta pressione (HPFP) - Posizione farfalla - Wastegate Duty-Cycle (WGDC) - RPM - Velocità - EGT E tanti altri… Monitor avanzato esclusivo MHD: - Correzioni temporali per cilindro - Aumenta il bersaglio EX che può leggere più in alto di 22.x psi (il canale target BMW boost non può) - Base Compressor Axis: Boost Setpoint, MAF req WGDC. - Limitatori di coppia attivi E tanti altri… --------------------------------------------- Queste opzioni flash possono essere applicate a qualsiasi mappa direttamente attraverso l'app: - Burm di scarico (durata e aggressività, velocità minima, giri min.) - Sensore mappa N20 (su N55) - Rimuovere il limitatore di velocità massima (Vmax) - Riduzione del rumore a freddo - Flap di scarico aperto in modalità sport - Limitare la potenza per ogni marcia - Supporto flash XHP TCU (mappe OTS ottimizzate) - Modalità di raffreddamento sportivo per un maggiore raffreddamento intercooler acqua / aria (solo B58) --------------------------------------------- Auto supportate: M135i F2x N55 2012 - 2016 M235i F2x N55 2013 - 2016 M2 F87 N55 2015 - 2018 335i N55 F3x 2011 - 2015 435i N55 F3x 2013 - 2016 535i / GT N55 F1x 2010 - 2017 640i N55 F0x 2011 - 2017 740i N55 F0x 2012 - 2015 X3 35i N55 F25 2010 - 2017 X4 35i / M40i N55 F26 2014 - 2018 X5 40i N55 F15 2013 - 2018 X6 40i N55 F16 2014 - 2018 M3 S55 F80 2014 - 2019 M4 S55 F82 2014 - 2019 M4 S55 F83 2014 - 2019 M140i F2x 2012 - 2019 M240i F2x 2016 - 2019 340i F3x 2015 - 2019 440i F3x 2016 - 2019 540i G3x 2017 - 640i GT G32 2017 - 740i G1x F0x 2015 - X3 M40i G01 2017 - X4 M40i G02 2018 - X5 40i G05 2018 - Z4 M40i G29 2019 - 114i F2x 2012 - 2015 116i F2x 2011 - 2015 118i F2x 2011 - 2016 120i F2x 2015 - 2017 316i F3x 2012 - 2018 X-Drive è supportato su tutte le auto. Sono supportate tutte le auto del kit di alimentazione delle prestazioni. Controlla la nostra home page / manuale per ulteriori informazioni e le modifiche consigliate per ogni fase. The MHD Flasher F+G Series is a complete flash tuning app for your BMW. Unlike a piggyback module, it is capable of complete DME remapping while retaining all OEM safety mechanisms. This allows for maximum performance,maximum safety, and unrivaled drivability. --------------------------------------------- Full OBD Flashing: You can install MHD right at home and start tuning immediately! There is no need to remove and send out your DME for a costly “unlock.” Simply download the MHD Flasher F-Series app that connects via a K+DCAN cable to your Android device and your vehicle’s OBD-II port, start the app, and within 15-25 minutes the initial installation is complete. Further map changes are much faster - only 1-3 minutes! You can revert your vehicle to the factory OEM flash at any point, and no initial backup is necessary. --------------------------------------------- Stage 1, Stage 2 und E85 OTS (Off The Shelf) Maps by PureBoost: N55 EWG (Vehicles built after 07/2013 with electronic wastegate): - Stage 1 (up to 360HP/540NM) (not available for M2 and X4 M40i) - Stage 2 (up to 390HP/580NM) - Stage 2+ (up to 430HP/630NM) - Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20% N55 PWG (pneumatic wastegate): - Stage 1 (up to 340HP/540NM) - Stage 2 (up to 370HP/580NM) - Stage 2+ (up to 400HP/630NM) - Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20% S55 (BMW M3 / M4 F8x): - Stage 1 (up to 530HP/700NM) - Stage 2 (up to 560HP/780NM) - Ethanol Mix Maps: Stage 1, 2 and 2+ E30 Maps for ethanol blends of 30% B58: - Stage 1 (up to 420HP/580NM) - Stage 2 (up to 470HP/630NM) - Ethanol Mix Maps: Stage 1, 2 Maps for ethanol blends of 30% --------------------------------------------- Monitor your engine behavior to make sure it is running perfectly using a configurable and very responsive gauge layout. 50+ engine parameters are available at a glance! These are some of the available monitors: - Boost, Boost Target - Lambda (AFR) - Intake Air Temp (IAT) - Ignition Timing per Cylinder - Coolant Temperature - Oil Temperature, Oil Pressure - Transmission Temperature - High Pressure Fuel Pump (HPFP) - Throttle Position - Wastegate Duty-Cycle (WGDC) - RPM - Speed - EGT And many more… MHD exclusive advanced monitor: - Timing Corrections per Cylinder - Boost target EX which can read higher than 22.x psi (the BMW boost target channel can't) - Base Compressor Axis: Boost Setpoint, MAF req WGDC. - Active Torque Limiters And many more… --------------------------------------------- These flash options can be applied to any map directly through the app: - Exhaust Burble (duration & aggressiveness, min speed, min rpm) - N20 Map Sensor (on N55) - Remove top speed limiter (Vmax) - Cold start noise reduction - Exhaust flap open in sport mode - Limit power per gear - XHP TCU flash support (optimizied OTS maps) - Sport cooling mode for increased water / air intercooler cooling (B58 only) --------------------------------------------- Supported Cars: M135i F2x N55 2012 - 2016 M235i F2x N55 2013 - 2016 M2 F87 N55 2015 - 2018 335i N55 F3x 2011 - 2015 435i N55 F3x 2013 - 2016 535i / GT N55 F1x 2010 - 2017 640i N55 F0x 2011 - 2017 740i N55 F0x 2012 - 2015 X3 35i N55 F25 2010 - 2017 X4 35i / M40i N55 F26 2014 - 2018 X5 40i N55 F15 2013 - 2018 X6 40i N55 F16 2014 - 2018 M3 S55 F80 2014 - 2019 M4 S55 F82 2014 - 2019 M4 S55 F83 2014 - 2019 M140i F2x 2012 - 2019 M240i F2x 2016 - 2019 340i F3x 2015 - 2019 440i F3x 2016 - 2019 540i G3x 2017 - 640i GT G32 2017 - 740i G1x F0x 2015 - X3 M40i G01 2017 - X4 M40i G02 2018 - X5 40i G05 2018 - Z4 M40i G29 2019 - 114i F2x 2012 - 2015 116i F2x 2011 - 2015 118i F2x 2011 - 2016 120i F2x 2015 - 2017 316i F3x 2012 - 2018 X-Drive is supported on all cars. All performance power kit cars are supported. Check out our homepage / user manual for more information and recommended modifications for each stage.