MHD F+G Series

The MHD Flasher F+G Series is a complete flash tuning app for your BMW. Unlike a piggyback module, it is capable of complete DME remapping while retaining all OEM safety mechanisms. This allows for maximum performance,maximum safety, and unrivaled drivability. --------------------------------------------- Full OBD Flashing: You can install MHD right at home and start tuning immediately! There is no need to remove and send out your DME for a costly “unlock.” Simply download the MHD Flasher F-Series app that connects via a K+DCAN cable to your Android device and your vehicle’s OBD-II port, start the app, and within 15-25 minutes the initial installation is complete. Further map changes are much faster - only 1-3 minutes! You can revert your vehicle to the factory OEM flash at any point, and no initial backup is necessary. --------------------------------------------- Stage 1, Stage 2 und E85 OTS (Off The Shelf) Maps by PureBoost: N55 EWG (Vehicles built after 07/2013 with electronic wastegate): - Stage 1 (up to 360HP/540NM) (not available for M2 and X4 M40i) - Stage 2 (up to 390HP/580NM) - Stage 2+ (up to 430HP/630NM) - Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20% N55 PWG (pneumatic wastegate): - Stage 1 (up to 340HP/540NM) - Stage 2 (up to 370HP/580NM) - Stage 2+ (up to 400HP/630NM) - Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20% S55 (BMW M3 / M4 F8x): - Stage 1 (up to 530HP/700NM) - Stage 2 (up to 560HP/780NM) - Ethanol Mix Maps: Stage 1, 2 and 2+ E30 Maps for ethanol blends of 30% B58: - Stage 1 (up to 420HP/580NM) - Stage 2 (up to 470HP/630NM) - Ethanol Mix Maps: Stage 1, 2 Maps for ethanol blends of 30% --------------------------------------------- Monitor your engine behavior to make sure it is running perfectly using a configurable and very responsive gauge layout. 50+ engine parameters are available at a glance! These are some of the available monitors: - Boost, Boost Target - Lambda (AFR) - Intake Air Temp (IAT) - Ignition Timing per Cylinder - Coolant Temperature - Oil Temperature, Oil Pressure - Transmission Temperature - High Pressure Fuel Pump (HPFP) - Throttle Position - Wastegate Duty-Cycle (WGDC) - RPM - Speed - EGT And many more… MHD exclusive advanced monitor: - Timing Corrections per Cylinder - Boost target EX which can read higher than 22.x psi (the BMW boost target channel can't) - Base Compressor Axis: Boost Setpoint, MAF req WGDC. - Active Torque Limiters And many more… --------------------------------------------- These flash options can be applied to any map directly through the app: - Exhaust Burble (duration & aggressiveness, min speed, min rpm) - N20 Map Sensor (on N55) - Remove top speed limiter (Vmax) - Cold start noise reduction - Exhaust flap open in sport mode - Limit power per gear - XHP TCU flash support (optimizied OTS maps) - Sport cooling mode for increased water / air intercooler cooling (B58 only) --------------------------------------------- Supported Cars: M135i F2x N55 2012 - 2016 M235i F2x N55 2013 - 2016 M2 F87 N55 2015 - 2018 335i N55 F3x 2011 - 2015 435i N55 F3x 2013 - 2016 535i / GT N55 F1x 2010 - 2017 640i N55 F0x 2011 - 2017 740i N55 F0x 2012 - 2015 X3 35i N55 F25 2010 - 2017 X4 35i / M40i N55 F26 2014 - 2018 X5 40i N55 F15 2013 - 2018 X6 40i N55 F16 2014 - 2018 M3 S55 F80 2014 - 2019 M4 S55 F82 2014 - 2019 M4 S55 F83 2014 - 2019 M140i F2x 2012 - 2019 M240i F2x 2016 - 2019 340i F3x 2015 - 2019 440i F3x 2016 - 2019 540i G3x 2017 - 640i GT G32 2017 - 740i G1x F0x 2015 - X3 M40i G01 2017 - X4 M40i G02 2018 - X5 40i G05 2018 - Z4 M40i G29 2019 - 114i F2x 2012 - 2015 116i F2x 2011 - 2015 118i F2x 2011 - 2016 120i F2x 2015 - 2017 316i F3x 2012 - 2018 X-Drive is supported on all cars. All performance power kit cars are supported. Check out our homepage / user manual for more information and recommended modifications for each stage. Seri MHD Flasher F + G adalah aplikasi penyetelan flash yang lengkap untuk BMW Anda. Tidak seperti modul piggyback, ini mampu menyelesaikan remapping DME sambil mempertahankan semua mekanisme keamanan OEM. Ini memungkinkan kinerja maksimum, keamanan maksimum, dan kecepatan berkendara yang tak tertandingi. --------------------------------------------- OBD Flashing Penuh: Anda dapat menginstal MHD di rumah dan mulai menyetel segera! Tidak perlu menghapus dan mengirim DME Anda untuk "membuka kunci" yang mahal. Cukup unduh aplikasi MHD Flasher F-Series yang terhubung melalui kabel K + DCAN ke perangkat Android Anda dan port OBD-II kendaraan Anda, mulai aplikasi , dan dalam 15-25 menit instalasi awal selesai. Perubahan peta lebih lanjut jauh lebih cepat - hanya 1-3 menit! Anda dapat mengembalikan kendaraan Anda ke kilat OEM pabrik kapan saja, dan tidak diperlukan cadangan awal. --------------------------------------------- Tahap 1, Tahap 2 dan E85 OTS (Off The Shelf) Peta oleh PureBoost: N55 EWG (Kendaraan yang dibangun setelah 07/2013 dengan wastegate elektronik): - Tahap 1 (hingga 360HP / 540NM) (tidak tersedia untuk M2 dan X4 M40i) - Tahap 2 (hingga 390HP / 580NM) - Tahap 2+ (hingga 430HP / 630NM) - Peta Campuran Etanol: Peta Tahap 1, 2 dan 2+ E20 untuk campuran etanol 20% N55 PWG (wastegate pneumatik): - Tahap 1 (hingga 340HP / 540NM) - Tahap 2 (hingga 370HP / 580NM) - Tahap 2+ (hingga 400HP / 630NM) - Peta Campuran Etanol: Peta Tahap 1, 2 dan 2+ E20 untuk campuran etanol 20% S55 (BMW M3 / M4 F8x): - Tahap 1 (hingga 530HP / 700NM) - Tahap 2 (hingga 560HP / 780NM) - Peta Campuran Etanol: Tahap 1, 2 dan 2+ Peta E30 untuk campuran etanol 30% B58: - Tahap 1 (hingga 420HP / 580NM) - Tahap 2 (hingga 470HP / 630NM) - Peta Campuran Etanol: Tahap 1, 2 Peta untuk campuran etanol 30% --------------------------------------------- Pantau perilaku engine Anda untuk memastikannya berjalan dengan sempurna menggunakan tata letak ukuran yang dapat dikonfigurasi dan sangat responsif. 50+ parameter engine tersedia dalam sekejap! Ini adalah beberapa monitor yang tersedia: - Boost, Boost Target - Lambda (AFR) - Intake Air Temp (IAT) - Waktu Pengapian per Silinder - Temperatur cairan pendingin - Suhu Minyak, Tekanan Minyak - Suhu Transmisi - Pompa Bahan Bakar Tekanan Tinggi (HPFP) - Posisi Throttle - Wastegate Duty-Cycle (WGDC) - RPM - Kecepatan - EGT Dan masih banyak lagi… Monitor canggih eksklusif MHD: - Koreksi Pengaturan Waktu per Silinder - Tingkatkan target EX yang bisa membaca lebih tinggi dari 22.x psi (saluran target dorongan BMW tidak bisa) - Sumbu Kompresor Dasar: Tingkatkan Setpoint, MAF req WGDC. - Pembatas Torsi Aktif Dan masih banyak lagi… --------------------------------------------- Opsi flash ini dapat diterapkan ke peta apa pun secara langsung melalui aplikasi: - Exhaust Burble (durasi & agresivitas, kecepatan min, min rpm) - Sensor Peta N20 (pada N55) - Hapus limiter kecepatan tinggi (Vmax) - Pengurangan kebisingan mulai dingin - Tutup knalpot terbuka dalam mode olahraga - Batasi daya per gigi - Dukungan flash XHP TCU (peta OTS yang dioptimalkan) - Mode pendinginan olahraga untuk peningkatan pendinginan intercooler air / udara (hanya B58) --------------------------------------------- Mobil yang didukung: M135i F2x N55 2012 - 2016 M235i F2x N55 2013 - 2016 M2 F87 N55 2015 - 2018 335i N55 F3x 2011 - 2015 435i N55 F3x 2013 - 2016 535i / GT N55 F1x 2010 - 2017 640i N55 F0x 2011 - 2017 740i N55 F0x 2012 - 2015 X3 35i N55 F25 2010 - 2017 X4 35i / M40i N55 F26 2014 - 2018 X5 40i N55 F15 2013 - 2018 X6 40i N55 F16 2014 - 2018 M3 S55 F80 2014 - 2019 M4 S55 F82 2014 - 2019 M4 S55 F83 2014 - 2019 M140i F2x 2012 - 2019 M240i F2x 2016 - 2019 340i F3x 2015 - 2019 440i F3x 2016 - 2019 540i G3x 2017 - 640i GT G32 2017 - 740i G1x F0x 2015 - X3 M40i G01 2017 - X4 M40i G02 2018 - X5 40i G05 2018 - Z4 M40i G29 2019 - 114i F2x 2012 - 2015 116i F2x 2011 - 2015 118i F2x 2011 - 2016 120i F2x 2015 - 2017 316i F3x 2012 - 2018 X-Drive didukung di semua mobil. Semua mobil power kit kinerja didukung. Lihat beranda / manual pengguna kami untuk informasi lebih lanjut dan modifikasi yang disarankan untuk setiap tahap. The MHD Flasher F+G Series is a complete flash tuning app for your BMW. Unlike a piggyback module, it is capable of complete DME remapping while retaining all OEM safety mechanisms. This allows for maximum performance,maximum safety, and unrivaled drivability. --------------------------------------------- Full OBD Flashing: You can install MHD right at home and start tuning immediately! There is no need to remove and send out your DME for a costly “unlock.” Simply download the MHD Flasher F-Series app that connects via a K+DCAN cable to your Android device and your vehicle’s OBD-II port, start the app, and within 15-25 minutes the initial installation is complete. Further map changes are much faster - only 1-3 minutes! You can revert your vehicle to the factory OEM flash at any point, and no initial backup is necessary. --------------------------------------------- Stage 1, Stage 2 und E85 OTS (Off The Shelf) Maps by PureBoost: N55 EWG (Vehicles built after 07/2013 with electronic wastegate): - Stage 1 (up to 360HP/540NM) (not available for M2 and X4 M40i) - Stage 2 (up to 390HP/580NM) - Stage 2+ (up to 430HP/630NM) - Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20% N55 PWG (pneumatic wastegate): - Stage 1 (up to 340HP/540NM) - Stage 2 (up to 370HP/580NM) - Stage 2+ (up to 400HP/630NM) - Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20% S55 (BMW M3 / M4 F8x): - Stage 1 (up to 530HP/700NM) - Stage 2 (up to 560HP/780NM) - Ethanol Mix Maps: Stage 1, 2 and 2+ E30 Maps for ethanol blends of 30% B58: - Stage 1 (up to 420HP/580NM) - Stage 2 (up to 470HP/630NM) - Ethanol Mix Maps: Stage 1, 2 Maps for ethanol blends of 30% --------------------------------------------- Monitor your engine behavior to make sure it is running perfectly using a configurable and very responsive gauge layout. 50+ engine parameters are available at a glance! These are some of the available monitors: - Boost, Boost Target - Lambda (AFR) - Intake Air Temp (IAT) - Ignition Timing per Cylinder - Coolant Temperature - Oil Temperature, Oil Pressure - Transmission Temperature - High Pressure Fuel Pump (HPFP) - Throttle Position - Wastegate Duty-Cycle (WGDC) - RPM - Speed - EGT And many more… MHD exclusive advanced monitor: - Timing Corrections per Cylinder - Boost target EX which can read higher than 22.x psi (the BMW boost target channel can't) - Base Compressor Axis: Boost Setpoint, MAF req WGDC. - Active Torque Limiters And many more… --------------------------------------------- These flash options can be applied to any map directly through the app: - Exhaust Burble (duration & aggressiveness, min speed, min rpm) - N20 Map Sensor (on N55) - Remove top speed limiter (Vmax) - Cold start noise reduction - Exhaust flap open in sport mode - Limit power per gear - XHP TCU flash support (optimizied OTS maps) - Sport cooling mode for increased water / air intercooler cooling (B58 only) --------------------------------------------- Supported Cars: M135i F2x N55 2012 - 2016 M235i F2x N55 2013 - 2016 M2 F87 N55 2015 - 2018 335i N55 F3x 2011 - 2015 435i N55 F3x 2013 - 2016 535i / GT N55 F1x 2010 - 2017 640i N55 F0x 2011 - 2017 740i N55 F0x 2012 - 2015 X3 35i N55 F25 2010 - 2017 X4 35i / M40i N55 F26 2014 - 2018 X5 40i N55 F15 2013 - 2018 X6 40i N55 F16 2014 - 2018 M3 S55 F80 2014 - 2019 M4 S55 F82 2014 - 2019 M4 S55 F83 2014 - 2019 M140i F2x 2012 - 2019 M240i F2x 2016 - 2019 340i F3x 2015 - 2019 440i F3x 2016 - 2019 540i G3x 2017 - 640i GT G32 2017 - 740i G1x F0x 2015 - X3 M40i G01 2017 - X4 M40i G02 2018 - X5 40i G05 2018 - Z4 M40i G29 2019 - 114i F2x 2012 - 2015 116i F2x 2011 - 2015 118i F2x 2011 - 2016 120i F2x 2015 - 2017 316i F3x 2012 - 2018 X-Drive is supported on all cars. All performance power kit cars are supported. Check out our homepage / user manual for more information and recommended modifications for each stage.