MQTT Alarm Control Panel

MQTT Alarm Control Panel Reuse and old Android devices as a home alarm control panel that integrates with Home Assistant or any home automation platform that supports MQTT messaging. MQTT Alarm Control Panel is an alarm control panel for use with home automation platforms that support MQTT messaging. The application was originally built for Home Assistant'sMQTT Manual Control Panel. However, the application can be used with any home automation platform that supports the MQTT messaging protocol such as Jeedom, openHab, or Node-Red. The alarm control panel acts as an interface for your home alarm system and allows for two way communication using MQTT. You can set the alarm state to away or home, or disarm the alarm using a code. Your home automation system controls the sensors or automation that triggers the siren or notifies users of possible intrusion. Features * Stream video, detect motion, detect faces, and read QR Codes. * Capture and emailing images when the alarm is disabled. MQTT commands to remotely control the application (speak text, play audio, display notifications, alerts). * Device sensor data reporting over MQTT (temperature, light, pressure, battery, etc.). * Day/Night mode themes based on MQTT sun value. * Fingerprint unlock support to disable the alarm. (on supported devices). * Optional screensaver mode using a digital clock or Imgur images. * Three day MQTT Weather forecast. * Home Automation Platform webpage support for viewing home automation dashboards. The alarm panel is designed to be used as a dedicated device which runs continuously in full-screen mode. The alarm panel is open source and available on GitHub. There is also a version that runs on a Raspberry Pi using Android Things For the complete setup instructions and additional information, please visit the Project Home Page. Home Assistant Home Assistant's MQTT Manual Alarm Control Panel Project's Home Page Raspberry Pi Version Support: [email protected] Panel Kontrol Alarm MQTT Penggunaan kembali dan perangkat Android lama sebagai panel kontrol alarm rumah yang terintegrasi dengan Home Assistant atau platform otomatisasi rumah apa pun yang mendukung pengiriman pesan MQTT. Panel Kontrol Alarm MQTT adalah panel kontrol alarm untuk digunakan dengan platform otomatisasi rumah yang mendukung pengiriman pesan MQTT. Aplikasi ini awalnya dibangun untuk Panel Kontrol Manual MQTT . Namun, aplikasi dapat digunakan dengan platform otomatisasi rumah yang mendukung protokol pengiriman pesan MQTT seperti Jeedom, openHab, atau Node-Red. Panel kontrol alarm bertindak sebagai antarmuka untuk sistem alarm rumah Anda dan memungkinkan komunikasi dua arah menggunakan MQTT. Anda dapat mengatur status alarm ke jauh atau rumah, atau melucuti alarm menggunakan kode. Sistem otomasi rumah Anda mengontrol sensor atau otomatisasi yang memicu sirene atau memberi tahu pengguna tentang kemungkinan gangguan. Fitur * Streaming video, deteksi gerakan, deteksi wajah, dan baca QR Codes. * Mengambil dan mengirim gambar melalui email saat alarm dinonaktifkan. Perintah MQTT untuk mengontrol aplikasi dari jarak jauh (berbicara teks, memutar audio, menampilkan notifikasi, peringatan). * Pelaporan data sensor perangkat melalui MQTT (suhu, cahaya, tekanan, baterai, dll.). * Tema mode Siang / Malam berdasarkan nilai matahari MQTT. * Dukungan membuka kunci sidik jari untuk menonaktifkan alarm. (pada perangkat yang didukung). * Mode screensaver opsional menggunakan jam digital atau gambar Imgur. * Prakiraan cuaca MQTT tiga hari. * Dukungan halaman web Home Automation Platform untuk melihat dasbor otomatisasi rumah. Panel alarm dirancang untuk digunakan sebagai perangkat khusus yang berjalan terus menerus dalam mode layar penuh. Panel alarm adalah sumber terbuka dan tersedia di GitHub. Ada juga versi yang berjalan pada Raspberry Pi menggunakan Android Things Untuk instruksi pengaturan lengkap dan informasi tambahan, silakan kunjungi Halaman Beranda Proyek . Asisten Rumah Panel Kontrol Alarm Manual Rumah MQTT Manual Asisten Halaman Utama Proyek Versi Raspberry Pi Dukungan: [email protected] MQTT Alarm Control Panel Reuse and old Android devices as a home alarm control panel that integrates with Home Assistant or any home automation platform that supports MQTT messaging. MQTT Alarm Control Panel is an alarm control panel for use with home automation platforms that support MQTT messaging. The application was originally built for Home Assistant'sMQTT Manual Control Panel. However, the application can be used with any home automation platform that supports the MQTT messaging protocol such as Jeedom, openHab, or Node-Red. The alarm control panel acts as an interface for your home alarm system and allows for two way communication using MQTT. You can set the alarm state to away or home, or disarm the alarm using a code. Your home automation system controls the sensors or automation that triggers the siren or notifies users of possible intrusion. Features * Stream video, detect motion, detect faces, and read QR Codes. * Capture and emailing images when the alarm is disabled. MQTT commands to remotely control the application (speak text, play audio, display notifications, alerts). * Device sensor data reporting over MQTT (temperature, light, pressure, battery, etc.). * Day/Night mode themes based on MQTT sun value. * Fingerprint unlock support to disable the alarm. (on supported devices). * Optional screensaver mode using a digital clock or Imgur images. * Three day MQTT Weather forecast. * Home Automation Platform webpage support for viewing home automation dashboards. The alarm panel is designed to be used as a dedicated device which runs continuously in full-screen mode. The alarm panel is open source and available on GitHub. There is also a version that runs on a Raspberry Pi using Android Things For the complete setup instructions and additional information, please visit the Project Home Page. Home Assistant Home Assistant's MQTT Manual Alarm Control Panel Project's Home Page Raspberry Pi Version Support: [email protected]