MHD F+G Series

The MHD Flasher F+G Series is a complete flash tuning app for your BMW. Unlike a piggyback module, it is capable of complete DME remapping while retaining all OEM safety mechanisms. This allows for maximum performance,maximum safety, and unrivaled drivability. --------------------------------------------- Full OBD Flashing: You can install MHD right at home and start tuning immediately! There is no need to remove and send out your DME for a costly “unlock.” Simply download the MHD Flasher F-Series app that connects via a K+DCAN cable to your Android device and your vehicle’s OBD-II port, start the app, and within 15-25 minutes the initial installation is complete. Further map changes are much faster - only 1-3 minutes! You can revert your vehicle to the factory OEM flash at any point, and no initial backup is necessary. --------------------------------------------- Stage 1, Stage 2 und E85 OTS (Off The Shelf) Maps by PureBoost: N55 EWG (Vehicles built after 07/2013 with electronic wastegate): - Stage 1 (up to 360HP/540NM) (not available for M2 and X4 M40i) - Stage 2 (up to 390HP/580NM) - Stage 2+ (up to 430HP/630NM) - Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20% N55 PWG (pneumatic wastegate): - Stage 1 (up to 340HP/540NM) - Stage 2 (up to 370HP/580NM) - Stage 2+ (up to 400HP/630NM) - Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20% S55 (BMW M3 / M4 F8x): - Stage 1 (up to 530HP/700NM) - Stage 2 (up to 560HP/780NM) - Ethanol Mix Maps: Stage 1, 2 and 2+ E30 Maps for ethanol blends of 30% B58: - Stage 1 (up to 420HP/580NM) - Stage 2 (up to 470HP/630NM) - Ethanol Mix Maps: Stage 1, 2 Maps for ethanol blends of 30% --------------------------------------------- Monitor your engine behavior to make sure it is running perfectly using a configurable and very responsive gauge layout. 50+ engine parameters are available at a glance! These are some of the available monitors: - Boost, Boost Target - Lambda (AFR) - Intake Air Temp (IAT) - Ignition Timing per Cylinder - Coolant Temperature - Oil Temperature, Oil Pressure - Transmission Temperature - High Pressure Fuel Pump (HPFP) - Throttle Position - Wastegate Duty-Cycle (WGDC) - RPM - Speed - EGT And many more… MHD exclusive advanced monitor: - Timing Corrections per Cylinder - Boost target EX which can read higher than 22.x psi (the BMW boost target channel can't) - Base Compressor Axis: Boost Setpoint, MAF req WGDC. - Active Torque Limiters And many more… --------------------------------------------- These flash options can be applied to any map directly through the app: - Exhaust Burble (duration & aggressiveness, min speed, min rpm) - N20 Map Sensor (on N55) - Remove top speed limiter (Vmax) - Cold start noise reduction - Exhaust flap open in sport mode - Limit power per gear - XHP TCU flash support (optimizied OTS maps) - Sport cooling mode for increased water / air intercooler cooling (B58 only) --------------------------------------------- Supported Cars: M135i F2x N55 2012 - 2016 M235i F2x N55 2013 - 2016 M2 F87 N55 2015 - 2018 335i N55 F3x 2011 - 2015 435i N55 F3x 2013 - 2016 535i / GT N55 F1x 2010 - 2017 640i N55 F0x 2011 - 2017 740i N55 F0x 2012 - 2015 X3 35i N55 F25 2010 - 2017 X4 35i / M40i N55 F26 2014 - 2018 X5 40i N55 F15 2013 - 2018 X6 40i N55 F16 2014 - 2018 M3 S55 F80 2014 - 2019 M4 S55 F82 2014 - 2019 M4 S55 F83 2014 - 2019 M140i F2x 2012 - 2019 M240i F2x 2016 - 2019 340i F3x 2015 - 2019 440i F3x 2016 - 2019 540i G3x 2017 - 640i GT G32 2017 - 740i G1x F0x 2015 - X3 M40i G01 2017 - X4 M40i G02 2018 - X5 40i G05 2018 - Z4 M40i G29 2019 - 114i F2x 2012 - 2015 116i F2x 2011 - 2015 118i F2x 2011 - 2016 120i F2x 2015 - 2017 316i F3x 2012 - 2018 X-Drive is supported on all cars. All performance power kit cars are supported. Check out our homepage / user manual for more information and recommended modifications for each stage. La serie MHD Flasher F + G es una completa aplicación de ajuste de flash para su BMW. A diferencia de un módulo de piggyback, es capaz de completar la reasignación de DME al tiempo que conserva todos los mecanismos de seguridad OEM. Esto permite el máximo rendimiento, la máxima seguridad y una manejabilidad sin igual. --------------------------------------------- Parpadeo completo del OBD: ¡Puedes instalar MHD desde casa y comenzar a sintonizar de inmediato! No es necesario quitar y enviar su DME para un costoso "desbloqueo". Simplemente descargue la aplicación MHD Flasher F-Series que se conecta a través de un cable K + DCAN a su dispositivo Android y al puerto OBD-II de su vehículo, inicie la aplicación , y dentro de 15-25 minutos se completa la instalación inicial. Más cambios en el mapa son mucho más rápidos, ¡solo 1-3 minutos! Puede revertir su vehículo al flash OEM de fábrica en cualquier momento y no es necesario realizar una copia de seguridad inicial. --------------------------------------------- Etapa 1, Etapa 2 y ETS OTS (Off The Shelf) de PureBoost: N55 EWG (Vehículos construidos después del 07/2013 con residuos electrónicos): - Etapa 1 (hasta 360HP / 540NM) (no disponible para M2 y X4 M40i) - Etapa 2 (hasta 390HP / 580NM) - Etapa 2+ (hasta 430HP / 630NM) - Mapas de mezcla de etanol: Etapa 1, 2 y 2+ Mapas E20 para mezclas de etanol del 20% N55 PWG (válvula de descarga neumática): - Etapa 1 (hasta 340HP / 540NM) - Etapa 2 (hasta 370HP / 580NM) - Etapa 2+ (hasta 400HP / 630NM) - Mapas de mezcla de etanol: Etapa 1, 2 y 2+ Mapas E20 para mezclas de etanol del 20% S55 (BMW M3 / M4 F8x): - Etapa 1 (hasta 530HP / 700NM) - Etapa 2 (hasta 560HP / 780NM) - Mapas de mezcla de etanol: Etapa 1, 2 y 2+ Mapas E30 para mezclas de etanol del 30% B58: - Etapa 1 (hasta 420HP / 580NM) - Etapa 2 (hasta 470HP / 630NM) - Mapas de mezcla de etanol: Etapa 1, 2 Mapas para mezclas de etanol del 30% --------------------------------------------- Monitoree el comportamiento de su motor para asegurarse de que funciona a la perfección con un diseño de calibre configurable y muy sensible. ¡Más de 50 parámetros del motor están disponibles de un vistazo! Estos son algunos de los monitores disponibles: - Boost, Boost Target - Lambda (AFR) - Temperatura del aire de admisión (IAT) - Tiempo de encendido por cilindro - Temperatura refrescante - Temperatura del aceite, presión del aceite - Temperatura de transmisión - Bomba de combustible de alta presión (HPFP) - La posición del acelerador - Wastegate Duty-Cycle (WGDC) - RPM - Velocidad - EGT Y muchos más… Monitor avanzado exclusivo MHD: - Correcciones de tiempo por cilindro - Aumente el EX objetivo que puede leer más de 22.x psi (el canal objetivo de impulso de BMW no puede) - Eje del compresor de la base: punto de ajuste de impulso, MAF req WGDC. - Limitadores de par activos Y muchos más… --------------------------------------------- Estas opciones de flash se pueden aplicar a cualquier mapa directamente a través de la aplicación: - Burble de escape (duración y agresividad, velocidad mínima, rpm mínima) - Sensor de mapa N20 (en N55) - Eliminar limitador de velocidad superior (Vmax) - Reducción de ruido de arranque en frío. - Aleta de escape abierta en modo deportivo. - Límite de potencia por engranaje. - Soporte de flash XHP TCU (mapas OTS optimizados) - Modo de enfriamiento deportivo para un mayor enfriamiento del enfriador de agua / aire (solo B58) --------------------------------------------- Coches soportados: M135i F2x N55 2012 - 2016 M235i F2x N55 2013 - 2016 M2 F87 N55 2015 - 2018 335i N55 F3x 2011 - 2015 435i N55 F3x 2013 - 2016 535i / GT N55 F1x 2010 - 2017 640i N55 F0x 2011 - 2017 740i N55 F0x 2012 - 2015 X3 35i N55 F25 2010 - 2017 X4 35i / M40i N55 F26 2014 - 2018 X5 40i N55 F15 2013 - 2018 X6 40i N55 F16 2014 - 2018 M3 S55 F80 2014 - 2019 M4 S55 F82 2014 - 2019 M4 S55 F83 2014 - 2019 M140i F2x 2012 - 2019 M240i F2x 2016 - 2019 340i F3x 2015 - 2019 440i F3x 2016 - 2019 540i G3x 2017 - 640i GT G32 2017 - 740i G1x F0x 2015 - X3 M40i G01 2017 - X4 M40i G02 2018 - X5 40i G05 2018 - Z4 M40i G29 2019 - 114i F2x 2012 - 2015 116i F2x 2011 - 2015 118i F2x 2011 - 2016 120i F2x 2015 - 2017 316i F3x 2012 - 2018 X-Drive es compatible con todos los coches. Todos los coches de kit de potencia de rendimiento son compatibles. Visite nuestra página de inicio / manual del usuario para obtener más información y las modificaciones recomendadas para cada etapa. The MHD Flasher F+G Series is a complete flash tuning app for your BMW. Unlike a piggyback module, it is capable of complete DME remapping while retaining all OEM safety mechanisms. This allows for maximum performance,maximum safety, and unrivaled drivability. --------------------------------------------- Full OBD Flashing: You can install MHD right at home and start tuning immediately! There is no need to remove and send out your DME for a costly “unlock.” Simply download the MHD Flasher F-Series app that connects via a K+DCAN cable to your Android device and your vehicle’s OBD-II port, start the app, and within 15-25 minutes the initial installation is complete. Further map changes are much faster - only 1-3 minutes! You can revert your vehicle to the factory OEM flash at any point, and no initial backup is necessary. --------------------------------------------- Stage 1, Stage 2 und E85 OTS (Off The Shelf) Maps by PureBoost: N55 EWG (Vehicles built after 07/2013 with electronic wastegate): - Stage 1 (up to 360HP/540NM) (not available for M2 and X4 M40i) - Stage 2 (up to 390HP/580NM) - Stage 2+ (up to 430HP/630NM) - Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20% N55 PWG (pneumatic wastegate): - Stage 1 (up to 340HP/540NM) - Stage 2 (up to 370HP/580NM) - Stage 2+ (up to 400HP/630NM) - Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20% S55 (BMW M3 / M4 F8x): - Stage 1 (up to 530HP/700NM) - Stage 2 (up to 560HP/780NM) - Ethanol Mix Maps: Stage 1, 2 and 2+ E30 Maps for ethanol blends of 30% B58: - Stage 1 (up to 420HP/580NM) - Stage 2 (up to 470HP/630NM) - Ethanol Mix Maps: Stage 1, 2 Maps for ethanol blends of 30% --------------------------------------------- Monitor your engine behavior to make sure it is running perfectly using a configurable and very responsive gauge layout. 50+ engine parameters are available at a glance! These are some of the available monitors: - Boost, Boost Target - Lambda (AFR) - Intake Air Temp (IAT) - Ignition Timing per Cylinder - Coolant Temperature - Oil Temperature, Oil Pressure - Transmission Temperature - High Pressure Fuel Pump (HPFP) - Throttle Position - Wastegate Duty-Cycle (WGDC) - RPM - Speed - EGT And many more… MHD exclusive advanced monitor: - Timing Corrections per Cylinder - Boost target EX which can read higher than 22.x psi (the BMW boost target channel can't) - Base Compressor Axis: Boost Setpoint, MAF req WGDC. - Active Torque Limiters And many more… --------------------------------------------- These flash options can be applied to any map directly through the app: - Exhaust Burble (duration & aggressiveness, min speed, min rpm) - N20 Map Sensor (on N55) - Remove top speed limiter (Vmax) - Cold start noise reduction - Exhaust flap open in sport mode - Limit power per gear - XHP TCU flash support (optimizied OTS maps) - Sport cooling mode for increased water / air intercooler cooling (B58 only) --------------------------------------------- Supported Cars: M135i F2x N55 2012 - 2016 M235i F2x N55 2013 - 2016 M2 F87 N55 2015 - 2018 335i N55 F3x 2011 - 2015 435i N55 F3x 2013 - 2016 535i / GT N55 F1x 2010 - 2017 640i N55 F0x 2011 - 2017 740i N55 F0x 2012 - 2015 X3 35i N55 F25 2010 - 2017 X4 35i / M40i N55 F26 2014 - 2018 X5 40i N55 F15 2013 - 2018 X6 40i N55 F16 2014 - 2018 M3 S55 F80 2014 - 2019 M4 S55 F82 2014 - 2019 M4 S55 F83 2014 - 2019 M140i F2x 2012 - 2019 M240i F2x 2016 - 2019 340i F3x 2015 - 2019 440i F3x 2016 - 2019 540i G3x 2017 - 640i GT G32 2017 - 740i G1x F0x 2015 - X3 M40i G01 2017 - X4 M40i G02 2018 - X5 40i G05 2018 - Z4 M40i G29 2019 - 114i F2x 2012 - 2015 116i F2x 2011 - 2015 118i F2x 2011 - 2016 120i F2x 2015 - 2017 316i F3x 2012 - 2018 X-Drive is supported on all cars. All performance power kit cars are supported. Check out our homepage / user manual for more information and recommended modifications for each stage.