The MHD Flasher F+G Series is a complete flash tuning app for your BMW. Unlike a piggyback module, it is capable of complete DME remapping while retaining all OEM safety mechanisms. This allows for maximum performance,maximum safety, and unrivaled drivability.
---------------------------------------------
Full OBD Flashing:
You can install MHD right at home and start tuning immediately! There is no need to remove and send out your DME for a costly “unlock.” Simply download the MHD Flasher F-Series app that connects via a K+DCAN cable to your Android device and your vehicle’s OBD-II port, start the app, and within 15-25 minutes the initial installation is complete. Further map changes are much faster - only 1-3 minutes! You can revert your vehicle to the factory OEM flash at any point, and no initial backup is necessary.
---------------------------------------------
Stage 1, Stage 2 und E85 OTS (Off The Shelf) Maps by PureBoost:
N55 EWG (Vehicles built after 07/2013 with electronic wastegate):
- Stage 1 (up to 360HP/540NM) (not available for M2 and X4 M40i)
- Stage 2 (up to 390HP/580NM)
- Stage 2+ (up to 430HP/630NM)
- Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20%
N55 PWG (pneumatic wastegate):
- Stage 1 (up to 340HP/540NM)
- Stage 2 (up to 370HP/580NM)
- Stage 2+ (up to 400HP/630NM)
- Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20%
S55 (BMW M3 / M4 F8x):
- Stage 1 (up to 530HP/700NM)
- Stage 2 (up to 560HP/780NM)
- Ethanol Mix Maps: Stage 1, 2 and 2+ E30 Maps for ethanol blends of 30%
B58:
- Stage 1 (up to 420HP/580NM)
- Stage 2 (up to 470HP/630NM)
- Ethanol Mix Maps: Stage 1, 2 Maps for ethanol blends of 30%
---------------------------------------------
Monitor your engine behavior to make sure it is running perfectly using a configurable and very responsive gauge layout. 50+ engine parameters are available at a glance!
These are some of the available monitors:
- Boost, Boost Target
- Lambda (AFR)
- Intake Air Temp (IAT)
- Ignition Timing per Cylinder
- Coolant Temperature
- Oil Temperature, Oil Pressure
- Transmission Temperature
- High Pressure Fuel Pump (HPFP)
- Throttle Position
- Wastegate Duty-Cycle (WGDC)
- RPM
- Speed
- EGT
And many more…
MHD exclusive advanced monitor:
- Timing Corrections per Cylinder
- Boost target EX which can read higher than 22.x psi (the BMW boost target channel can't)
- Base Compressor Axis: Boost Setpoint, MAF req WGDC.
- Active Torque Limiters
And many more…
---------------------------------------------
These flash options can be applied to any map directly through the app:
- Exhaust Burble (duration & aggressiveness, min speed, min rpm)
- N20 Map Sensor (on N55)
- Remove top speed limiter (Vmax)
- Cold start noise reduction
- Exhaust flap open in sport mode
- Limit power per gear
- XHP TCU flash support (optimizied OTS maps)
- Sport cooling mode for increased water / air intercooler cooling (B58 only)
---------------------------------------------
Supported Cars:
M135i F2x N55 2012 - 2016
M235i F2x N55 2013 - 2016
M2 F87 N55 2015 - 2018
335i N55 F3x 2011 - 2015
435i N55 F3x 2013 - 2016
535i / GT N55 F1x 2010 - 2017
640i N55 F0x 2011 - 2017
740i N55 F0x 2012 - 2015
X3 35i N55 F25 2010 - 2017
X4 35i / M40i N55 F26 2014 - 2018
X5 40i N55 F15 2013 - 2018
X6 40i N55 F16 2014 - 2018
M3 S55 F80 2014 - 2019
M4 S55 F82 2014 - 2019
M4 S55 F83 2014 - 2019
M140i F2x 2012 - 2019
M240i F2x 2016 - 2019
340i F3x 2015 - 2019
440i F3x 2016 - 2019
540i G3x 2017 -
640i GT G32 2017 -
740i G1x F0x 2015 -
X3 M40i G01 2017 -
X4 M40i G02 2018 -
X5 40i G05 2018 -
Z4 M40i G29 2019 -
114i F2x 2012 - 2015
116i F2x 2011 - 2015
118i F2x 2011 - 2016
120i F2x 2015 - 2017
316i F3x 2012 - 2018
X-Drive is supported on all cars.
All performance power kit cars are supported.
Check out our homepage / user manual for more information and recommended modifications for each stage.
MHD Flasher F + G Series هو تطبيق ضبط فلاش كامل لسيارات BMW الخاصة بك. على عكس الوحدة النمطية للخلفية ، فهي قادرة على إعادة رسم خرائط DME كاملة مع الحفاظ على جميع آليات السلامة الخاصة بشركة OEM. هذا يسمح لأداء أقصى ، أقصى قدر من السلامة ، وقيادة لا تضاهى.
---------------------------------------------
وامض كامل OBD:
يمكنك تثبيت MHD مباشرة في المنزل وبدء الضبط على الفور! ليست هناك حاجة لإزالة وإرسال DME الخاص بك للحصول على "فتح" مكلف. ببساطة قم بتنزيل تطبيق MHD Flasher F-Series الذي يتصل عبر كابل K + DCAN بجهاز Android ومنفذ OBD-II في سيارتك ، ابدأ تشغيل التطبيق وخلال 15-25 دقيقة اكتمال التثبيت الأولي. تغييرات الخريطة الإضافية أسرع بكثير - فقط 1-3 دقائق! يمكنك إعادة سيارتك إلى فلاش OEM الخاص بالمصنع في أي وقت ، ولا يلزم وجود نسخة احتياطية أولية.
---------------------------------------------
خرائط Stage 1 ، Stage 2 und E85 OTS (Off The Shelf) بواسطة PureBoost:
N55 EWG (المركبات التي بنيت بعد 07/2013 مع النفايات الإلكترونية):
- المرحلة 1 (حتى 360HP / 540NM) (غير متوفرة للطرازين M2 و X4 M40i)
- المرحلة 2 (حتى 390 حصان / 580 نانومتر)
- المرحلة 2+ (حتى 430HP / 630NM)
- خرائط مزيج الإيثانول: خرائط المرحلة 1 و 2 و 2+ E20 لمزج الإيثانول بنسبة 20 ٪
N55 PWG (الإسراف الهوائي):
- المرحلة الأولى (حتى 340 حصان / 540 نانومتر)
- المرحلة 2 (حتى 370 حصان / 580 نانومتر)
- المرحلة 2+ (حتى 400 حصان / 630 نانومتر)
- خرائط مزيج الإيثانول: خرائط المرحلة 1 و 2 و 2+ E20 لمزج الإيثانول بنسبة 20 ٪
S55 (BMW M3 / M4 F8x):
- المرحلة الأولى (حتى 530 حصان / 700 نيوتن متر)
- المرحلة 2 (حتى 560HP / 780NM)
- خرائط مزيج الإيثانول: خرائط المرحلة 1 و 2 و 2+ E30 لمزج الإيثانول بنسبة 30 ٪
B58:
- المرحلة الأولى (حتى 420 حصان / 580 نانومتر)
- المرحلة 2 (حتى 470HP / 630NM)
- خرائط مزيج الإيثانول: المرحلة الأولى ، خرائطان لمزج الإيثانول بنسبة 30٪
---------------------------------------------
راقب سلوك المحرك لديك للتأكد من أنه يعمل بشكل مثالي باستخدام تخطيط قياس قابل للتكوين وسريع الاستجابة. 50+ معلمات المحرك متوفرة في لمحة!
هذه بعض الشاشات المتوفرة:
- دفعة ، الهدف الهدف
- لامدا (AFR)
- درجة حرارة الهواء المدخول (IAT)
- توقيت الإشعال في الاسطوانة
- حرارة المبرد
- درجة حرارة الزيت ، ضغط الزيت
- درجة حرارة الإرسال
- مضخة الوقود ذات الضغط العالي (HPFP)
- موقف خنق
- Wastegate - واجب دورة (WGDC)
- دورة في الدقيقة
- سرعة
- EGT
و أكثر من ذلك بكثير…
MHD رصد حصرية متقدمة:
- تصحيحات التوقيت لكل أسطوانة
- تعزيز الهدف EX الذي يمكنه قراءة أعلى من 22.x رطل (لا يمكن للقناة المستهدفة في BMW تعزيز)
- محور الضاغط الأساسي: Boost Setpoint ، MAF req WGDC.
- محددات عزم الدوران النشط
و أكثر من ذلك بكثير…
---------------------------------------------
يمكن تطبيق خيارات الفلاش هذه على أي خريطة مباشرة من خلال التطبيق:
- العادم Burble (المدة والعدوانية ، دقيقة السرعة ، دقيقة دورة في الدقيقة)
- N20 Map Sensor (على N55)
- إزالة محدد السرعة القصوى (Vmax)
- بدء الضجيج البارد
- رفرف العادم مفتوح في الوضع الرياضي
- الحد من الطاقة لكل العتاد
- دعم الفلاش XHP TCU (خرائط OTS المحسنة)
- وضع التبريد الرياضي لزيادة تبريد المبرد بالماء / الهواء (B58 فقط)
---------------------------------------------
السيارات المدعومة:
M135i F2x N55 2012 - 2016
M235i F2x N55 2013 - 2016
M2 F87 N55 2015 - 2018
335i N55 F3x 2011 - 2015
435i N55 F3x 2013 - 2016
535i / GT N55 F1x 2010 - 2017
640i N55 F0x 2011 - 2017
740i N55 F0x 2012 - 2015
X3 35i N55 F25 2010 - 2017
X4 35i / M40i N55 F26 2014 - 2018
X5 40i N55 F15 2013 - 2018
X6 40i N55 F16 2014 - 2018
M3 S55 F80 2014 - 2019
M4 S55 F82 2014 - 2019
M4 S55 F83 2014 - 2019
M140i F2x 2012 - 2019
M240i F2x 2016 - 2019
340i F3x 2015 - 2019
440i F3x 2016 - 2019
540i G3x 2017 -
640i GT G32 2017 -
740i G1x F0x 2015 -
X3 M40i G01 2017 -
X4 M40i G02 2018 -
X5 40i G05 2018 -
Z4 M40i G29 2019 -
114i F2x 2012 - 2015
116i F2x 2011 - 2015
118i F2x 2011 - 2016
120i F2x 2015 - 2017
316i F3x 2012 - 2018
X-Drive معتمد على جميع السيارات.
ويدعم جميع سيارات السلطة عدة الأداء.
تحقق من الصفحة الرئيسية / دليل المستخدم لمزيد من المعلومات والتعديلات الموصى بها لكل مرحلة
The MHD Flasher F+G Series is a complete flash tuning app for your BMW. Unlike a piggyback module, it is capable of complete DME remapping while retaining all OEM safety mechanisms. This allows for maximum performance,maximum safety, and unrivaled drivability.
---------------------------------------------
Full OBD Flashing:
You can install MHD right at home and start tuning immediately! There is no need to remove and send out your DME for a costly “unlock.” Simply download the MHD Flasher F-Series app that connects via a K+DCAN cable to your Android device and your vehicle’s OBD-II port, start the app, and within 15-25 minutes the initial installation is complete. Further map changes are much faster - only 1-3 minutes! You can revert your vehicle to the factory OEM flash at any point, and no initial backup is necessary.
---------------------------------------------
Stage 1, Stage 2 und E85 OTS (Off The Shelf) Maps by PureBoost:
N55 EWG (Vehicles built after 07/2013 with electronic wastegate):
- Stage 1 (up to 360HP/540NM) (not available for M2 and X4 M40i)
- Stage 2 (up to 390HP/580NM)
- Stage 2+ (up to 430HP/630NM)
- Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20%
N55 PWG (pneumatic wastegate):
- Stage 1 (up to 340HP/540NM)
- Stage 2 (up to 370HP/580NM)
- Stage 2+ (up to 400HP/630NM)
- Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20%
S55 (BMW M3 / M4 F8x):
- Stage 1 (up to 530HP/700NM)
- Stage 2 (up to 560HP/780NM)
- Ethanol Mix Maps: Stage 1, 2 and 2+ E30 Maps for ethanol blends of 30%
B58:
- Stage 1 (up to 420HP/580NM)
- Stage 2 (up to 470HP/630NM)
- Ethanol Mix Maps: Stage 1, 2 Maps for ethanol blends of 30%
---------------------------------------------
Monitor your engine behavior to make sure it is running perfectly using a configurable and very responsive gauge layout. 50+ engine parameters are available at a glance!
These are some of the available monitors:
- Boost, Boost Target
- Lambda (AFR)
- Intake Air Temp (IAT)
- Ignition Timing per Cylinder
- Coolant Temperature
- Oil Temperature, Oil Pressure
- Transmission Temperature
- High Pressure Fuel Pump (HPFP)
- Throttle Position
- Wastegate Duty-Cycle (WGDC)
- RPM
- Speed
- EGT
And many more…
MHD exclusive advanced monitor:
- Timing Corrections per Cylinder
- Boost target EX which can read higher than 22.x psi (the BMW boost target channel can't)
- Base Compressor Axis: Boost Setpoint, MAF req WGDC.
- Active Torque Limiters
And many more…
---------------------------------------------
These flash options can be applied to any map directly through the app:
- Exhaust Burble (duration & aggressiveness, min speed, min rpm)
- N20 Map Sensor (on N55)
- Remove top speed limiter (Vmax)
- Cold start noise reduction
- Exhaust flap open in sport mode
- Limit power per gear
- XHP TCU flash support (optimizied OTS maps)
- Sport cooling mode for increased water / air intercooler cooling (B58 only)
---------------------------------------------
Supported Cars:
M135i F2x N55 2012 - 2016
M235i F2x N55 2013 - 2016
M2 F87 N55 2015 - 2018
335i N55 F3x 2011 - 2015
435i N55 F3x 2013 - 2016
535i / GT N55 F1x 2010 - 2017
640i N55 F0x 2011 - 2017
740i N55 F0x 2012 - 2015
X3 35i N55 F25 2010 - 2017
X4 35i / M40i N55 F26 2014 - 2018
X5 40i N55 F15 2013 - 2018
X6 40i N55 F16 2014 - 2018
M3 S55 F80 2014 - 2019
M4 S55 F82 2014 - 2019
M4 S55 F83 2014 - 2019
M140i F2x 2012 - 2019
M240i F2x 2016 - 2019
340i F3x 2015 - 2019
440i F3x 2016 - 2019
540i G3x 2017 -
640i GT G32 2017 -
740i G1x F0x 2015 -
X3 M40i G01 2017 -
X4 M40i G02 2018 -
X5 40i G05 2018 -
Z4 M40i G29 2019 -
114i F2x 2012 - 2015
116i F2x 2011 - 2015
118i F2x 2011 - 2016
120i F2x 2015 - 2017
316i F3x 2012 - 2018
X-Drive is supported on all cars.
All performance power kit cars are supported.
Check out our homepage / user manual for more information and recommended modifications for each stage.