MHD F+G Series

The MHD Flasher F+G Series is a complete flash tuning app for your BMW. Unlike a piggyback module, it is capable of complete DME remapping while retaining all OEM safety mechanisms. This allows for maximum performance,maximum safety, and unrivaled drivability. --------------------------------------------- Full OBD Flashing: You can install MHD right at home and start tuning immediately! There is no need to remove and send out your DME for a costly “unlock.” Simply download the MHD Flasher F-Series app that connects via a K+DCAN cable to your Android device and your vehicle’s OBD-II port, start the app, and within 15-25 minutes the initial installation is complete. Further map changes are much faster - only 1-3 minutes! You can revert your vehicle to the factory OEM flash at any point, and no initial backup is necessary. --------------------------------------------- Stage 1, Stage 2 und E85 OTS (Off The Shelf) Maps by PureBoost: N55 EWG (Vehicles built after 07/2013 with electronic wastegate): - Stage 1 (up to 360HP/540NM) (not available for M2 and X4 M40i) - Stage 2 (up to 390HP/580NM) - Stage 2+ (up to 430HP/630NM) - Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20% N55 PWG (pneumatic wastegate): - Stage 1 (up to 340HP/540NM) - Stage 2 (up to 370HP/580NM) - Stage 2+ (up to 400HP/630NM) - Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20% S55 (BMW M3 / M4 F8x): - Stage 1 (up to 530HP/700NM) - Stage 2 (up to 560HP/780NM) - Ethanol Mix Maps: Stage 1, 2 and 2+ E30 Maps for ethanol blends of 30% B58: - Stage 1 (up to 420HP/580NM) - Stage 2 (up to 470HP/630NM) - Ethanol Mix Maps: Stage 1, 2 Maps for ethanol blends of 30% --------------------------------------------- Monitor your engine behavior to make sure it is running perfectly using a configurable and very responsive gauge layout. 50+ engine parameters are available at a glance! These are some of the available monitors: - Boost, Boost Target - Lambda (AFR) - Intake Air Temp (IAT) - Ignition Timing per Cylinder - Coolant Temperature - Oil Temperature, Oil Pressure - Transmission Temperature - High Pressure Fuel Pump (HPFP) - Throttle Position - Wastegate Duty-Cycle (WGDC) - RPM - Speed - EGT And many more… MHD exclusive advanced monitor: - Timing Corrections per Cylinder - Boost target EX which can read higher than 22.x psi (the BMW boost target channel can't) - Base Compressor Axis: Boost Setpoint, MAF req WGDC. - Active Torque Limiters And many more… --------------------------------------------- These flash options can be applied to any map directly through the app: - Exhaust Burble (duration & aggressiveness, min speed, min rpm) - N20 Map Sensor (on N55) - Remove top speed limiter (Vmax) - Cold start noise reduction - Exhaust flap open in sport mode - Limit power per gear - XHP TCU flash support (optimizied OTS maps) - Sport cooling mode for increased water / air intercooler cooling (B58 only) --------------------------------------------- Supported Cars: M135i F2x N55 2012 - 2016 M235i F2x N55 2013 - 2016 M2 F87 N55 2015 - 2018 335i N55 F3x 2011 - 2015 435i N55 F3x 2013 - 2016 535i / GT N55 F1x 2010 - 2017 640i N55 F0x 2011 - 2017 740i N55 F0x 2012 - 2015 X3 35i N55 F25 2010 - 2017 X4 35i / M40i N55 F26 2014 - 2018 X5 40i N55 F15 2013 - 2018 X6 40i N55 F16 2014 - 2018 M3 S55 F80 2014 - 2019 M4 S55 F82 2014 - 2019 M4 S55 F83 2014 - 2019 M140i F2x 2012 - 2019 M240i F2x 2016 - 2019 340i F3x 2015 - 2019 440i F3x 2016 - 2019 540i G3x 2017 - 640i GT G32 2017 - 740i G1x F0x 2015 - X3 M40i G01 2017 - X4 M40i G02 2018 - X5 40i G05 2018 - Z4 M40i G29 2019 - 114i F2x 2012 - 2015 116i F2x 2011 - 2015 118i F2x 2011 - 2016 120i F2x 2015 - 2017 316i F3x 2012 - 2018 X-Drive is supported on all cars. All performance power kit cars are supported. Check out our homepage / user manual for more information and recommended modifications for each stage. The MHD Flasher F+G Series is a complete flash tuning app for your BMW. Unlike a piggyback module, it is capable of complete DME remapping while retaining all OEM safety mechanisms. This allows for maximum performance,maximum safety, and unrivaled drivability. --------------------------------------------- Full OBD Flashing: You can install MHD right at home and start tuning immediately! There is no need to remove and send out your DME for a costly “unlock.” Simply download the MHD Flasher F-Series app that connects via a K+DCAN cable to your Android device and your vehicle’s OBD-II port, start the app, and within 15-25 minutes the initial installation is complete. Further map changes are much faster - only 1-3 minutes! You can revert your vehicle to the factory OEM flash at any point, and no initial backup is necessary. --------------------------------------------- Stage 1, Stage 2 und E85 OTS (Off The Shelf) Maps by PureBoost: N55 EWG (Vehicles built after 07/2013 with electronic wastegate): - Stage 1 (up to 360HP/540NM) (not available for M2 and X4 M40i) - Stage 2 (up to 390HP/580NM) - Stage 2+ (up to 430HP/630NM) - Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20% N55 PWG (pneumatic wastegate): - Stage 1 (up to 340HP/540NM) - Stage 2 (up to 370HP/580NM) - Stage 2+ (up to 400HP/630NM) - Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20% S55 (BMW M3 / M4 F8x): - Stage 1 (up to 530HP/700NM) - Stage 2 (up to 560HP/780NM) - Ethanol Mix Maps: Stage 1, 2 and 2+ E30 Maps for ethanol blends of 30% B58: - Stage 1 (up to 420HP/580NM) - Stage 2 (up to 470HP/630NM) - Ethanol Mix Maps: Stage 1, 2 Maps for ethanol blends of 30% --------------------------------------------- Monitor your engine behavior to make sure it is running perfectly using a configurable and very responsive gauge layout. 50+ engine parameters are available at a glance! These are some of the available monitors: - Boost, Boost Target - Lambda (AFR) - Intake Air Temp (IAT) - Ignition Timing per Cylinder - Coolant Temperature - Oil Temperature, Oil Pressure - Transmission Temperature - High Pressure Fuel Pump (HPFP) - Throttle Position - Wastegate Duty-Cycle (WGDC) - RPM - Speed - EGT And many more… MHD exclusive advanced monitor: - Timing Corrections per Cylinder - Boost target EX which can read higher than 22.x psi (the BMW boost target channel can't) - Base Compressor Axis: Boost Setpoint, MAF req WGDC. - Active Torque Limiters And many more… --------------------------------------------- These flash options can be applied to any map directly through the app: - Exhaust Burble (duration & aggressiveness, min speed, min rpm) - N20 Map Sensor (on N55) - Remove top speed limiter (Vmax) - Cold start noise reduction - Exhaust flap open in sport mode - Limit power per gear - XHP TCU flash support (optimizied OTS maps) - Sport cooling mode for increased water / air intercooler cooling (B58 only) --------------------------------------------- Supported Cars: M135i F2x N55 2012 - 2016 M235i F2x N55 2013 - 2016 M2 F87 N55 2015 - 2018 335i N55 F3x 2011 - 2015 435i N55 F3x 2013 - 2016 535i / GT N55 F1x 2010 - 2017 640i N55 F0x 2011 - 2017 740i N55 F0x 2012 - 2015 X3 35i N55 F25 2010 - 2017 X4 35i / M40i N55 F26 2014 - 2018 X5 40i N55 F15 2013 - 2018 X6 40i N55 F16 2014 - 2018 M3 S55 F80 2014 - 2019 M4 S55 F82 2014 - 2019 M4 S55 F83 2014 - 2019 M140i F2x 2012 - 2019 M240i F2x 2016 - 2019 340i F3x 2015 - 2019 440i F3x 2016 - 2019 540i G3x 2017 - 640i GT G32 2017 - 740i G1x F0x 2015 - X3 M40i G01 2017 - X4 M40i G02 2018 - X5 40i G05 2018 - Z4 M40i G29 2019 - 114i F2x 2012 - 2015 116i F2x 2011 - 2015 118i F2x 2011 - 2016 120i F2x 2015 - 2017 316i F3x 2012 - 2018 X-Drive is supported on all cars. All performance power kit cars are supported. Check out our homepage / user manual for more information and recommended modifications for each stage.